管道除铁器安装有哪些注意事项？

What are the notices for the installation of the pipe iron remover?

管道除铁器本身设备安装并不复杂，但是在安装调整过程中有以下几点要多加注意：

The installation of pipeline iron remover itself is not complicated, but in the process of installation and adjustment, we should pay more attention to the following points:

1、管道除铁器电控系统可直接接入电源，设备单独工作，也可受控于粉料输送系统，该系统的启闭决定本设备的工作与否；

1. The electric control system of the pipe iron remover can directly connect to the power supply, and the equipment work alone, and can also be controlled by the powder conveying system. The system's opening and closing determines whether the equipment is working or not.

2、管道除铁器安装倾角（入、出料口中心线与水平面的夹角）在55度-60度为宜；两侧方向不可倾斜（即电机轴线保持水平）。出料口不应与出铁管道密闭连接，以长方形接铁斗或槽型接铁槽接铁，出铁口不应与出铁管道密闭连接，以长方形接铁斗或槽型接铁槽接铁，出铁口与接铁斗间距60mm为宜，以便必要时手工清除出铁口内可能出现的阻碍物（铁丝、物料块等）。

2, the installation inclination of the pipe iron remover (entry, the angle of the center line of the outlet and the angle of the horizontal plane) is appropriate at 55 degrees -60 degrees; the direction of the two sides can not be tilted (i.e. the axis of the motor is maintained). The outlet should not be connected with the iron pipe, the iron pipe is connected with the rectangular iron bucket or the groove type iron groove. The outlet should not be connected with the iron pipe, and the iron pipe is connected with the rectangular iron bucket or the groove type iron slot. The distance between the iron outlet and the iron bucket is 60mm, so that the possible obstacles in the iron outlet should be removed if necessary (Tie Si). A material block, etc.).

3、出、入口法兰连接面间必须垫入垫片或石棉绳，确保连接处的密封性能，以免粉尘溢出污染环境。

3. The gasket or asbestos rope must be padded between the outlet and inlet flange joints to ensure the sealing performance of the joint so as not to spilt the dust and pollute the environment.

4、使用前应根据粉体中铁磁性杂物的混入量，适当调整电机的开停时间，调整电控箱中时间继电器的按钮，即可改变这两个时间，其数值可直接在按钮上观察。参考选用时间为：运动时间10秒；间歇时间3-10分。用户可通过使用、观察、检验，按每次排铁量不超过3kg自行确定最佳时间，若粉料中含铁较多或粉料温度过高时，也可采用减速机连续运转的工作方式。

4. Before use, we should adjust the opening and stopping time of the motor and adjust the button of the time relay in the electric control box to change these two times, and the value can be observed directly on the button. The reference time is: 10 seconds for exercise time and 3-10 minutes for intermittent time. Through use, observation and inspection, the user can determine the best time by itself according to the amount of iron not exceeding 3kg each time. If the iron contains more iron or the temperature of the powder is too high, it can also use the working mode of continuous operation of the reducer.

5、接电后第一次开机必须观察设备运行方向是否正确，以下两种方法均可：

5, after the first switch on, the operation of the equipment must be observed correctly. The following two methods can be used:

   A、观察减速机转向，其旋转方向根据链瓦上标箭头方向一致。

A and observe the steering of the reducer. The direction of rotation is in accordance with the direction of the arrow on the chain tile.

   B、打开机侧观察口，将一粒直径小于22mm的铁磁物（螺母等）置于吸附隔板表面，该物向下方出铁口运动为正确。若运动方向不正确，应立即关机，改变电机旋转方向后再试。

B, open the machine side observation port, a particle of less than 22mm of iron magnetic material (nut, etc.) placed on the surface of the adsorption separator, the object is correct to the bottom outlet. If the direction of movement is not correct, turn off the motor immediately, change the direction of rotation of the motor and try again.

6、任何情况下均不允许过大铁块（≥0.1kg，长度≥80mm）进入机内，以免造成磁铁组故障或影响除铁效果。

6, under any circumstances, large iron blocks (greater than 0.1kg, length equal to 80mm) should not be allowed to enter the machine, so as to avoid the failure of the magnet group or affect the iron removal effect.